UK Battery Charger store >> Battery Charger >> BELL AND HOWELL Battery Charger suitable for BELL AND HOWELL

Please Press 'Ctrl + F' to locate your drill battery number or Machine Model.

Use our cross-reference information to choose the correct BELL AND HOWELL Battery Charger on Toppower(UK) Shipping. select high quality and lower price BELL AND HOWELL battery charger part NO. or the machine NO. bellow:
This is also compatible with the following models of BELL AND HOWELL
960 NP PZ1000 PZ2000
PZ2200 PZ3000 PZ3000D
PZ3200 PZ3300

BELL AND HOWELL Battery Charge Tips

1. If your BELL AND HOWELL battery can not charge with our BELL AND HOWELL battery charger, what is matter with the charger?

I think there is some electrical contact problem in your BELL AND HOWELL charger and you can fix it yourself in a few minutes.

(1). Remove your BELL AND HOWELL charger from the DC adapter.
(2). There are two hooks at the bottom of the BELL AND HOWELL charger.
(3). Your can release the top charging plate by pushing the hooks with two fingers.
(4). The top charging plate will release from the top.
(5). At the bottom of the charging plate, there will be three metallic contacts.
(6). Try pulling all the contacts so that it will avoid the bad connection.
(7). Slowly re-insert the charging plate to the charging base.
(8). Re-connect the DC adapter and your BELL AND HOWELL charger should work.

Good luck and if there is still other problem, please don't hesitate to send us a mail again.

2. What does the light indicator mean when charging BELL AND HOWELL battery ?

(1).Plug the AC power adapter in a wall outlet.
(2). Connect the AC Power adaptor supplied with BELL AND HOWELL charger to the DC in jack.
(3). "Status" indicator shows RED when the BELL AND HOWELL charger is ready and "Charger" indicator shows flashing Green when waiting for battery pack.
(4). Slide BELL AND HOWELL battery pack in the charger and "Charger" indicator goes RED when charging.
(5). "Charger" indicator show RED and GREEN alternatively when BELL AND HOWELL battery pack has more than 90% charged.
(6).When the BELL AND HOWELL battery pack is fully charged, the "Charger" indicator shows a steady green.
(7). After the BELL AND HOWELL battery pack fully charged, slide the battery pack out.
(8). Unplug DC power, "CHARGE" and "STATUS" indicators go out.

3.How to Test a BELL AND HOWELL Battery Charger

Whether you're unsure that your BELL AND HOWELL battery charger is working properly. Running a test on you BELL AND HOWELL battery charger is an easy process to solve this problem.

(1).Plug in your BELL AND HOWELL charger to an electrical outlet. Remove any batteries you may have charging in the unit.

(2).Turn on your voltmeter unit. Be sure there's power getting to the meter. Plug in the test probes into the voltmeter according to the meter's instructions. Set the selector switch to the highest level for DC Volt or whatever is recommended in the meter's instructions.

(3).Take a battery or battery pack that's compatible to your battery charger. Make sure the BELL AND HOWELL battery has no corrosion and is not leaking fluid. Touch the positive end of the battery with the red probe. Take the black test probe and place it on the negative side of the battery.

(4).Check the readout on the voltmeter and see where the pointer is indicating to. If it's on the left side, or negative side, switch the test probes. If it's on the right side, it will show that the BELL AND HOWELL battery is receiving some charge. Where it points to on the meter will determine how much charge it received.

(5).Check the BELL AND HOWELL battery charger to see how much power it's giving off, if you continue to receive a negative reading from the batteries. A negative reading will indicate a bad battery charger, and you should replace it. If the charger has sufficient amount of power flowing through it, it's more than likely the BELL AND HOWELL batteries are bad and just won't hold a charge.