UK Battery Charger store >> Battery Charger >> CONTAX Battery Charger suitable for CONTAX

Please Press 'Ctrl + F' to locate your drill battery number or Machine Model.

Use our cross-reference information to choose the correct CONTAX Battery Charger on Toppower(UK) Shipping. select high quality and lower price CONTAX battery charger part NO. or the machine NO. bellow:
This Battery Charger can replace the following part numbers of CONTAX
2CR5 BP-1100S BP-760S CR-2
CR2
This is also compatible with the following models of CONTAX
645 Aria AX
G1 G2 i4R
i4RB i4RBK III
N1 NX RTS
RTS III RX RX II
T2 T2 Date T3
Tix TLA 200 TVS
TVS DataBack Tvs Digital TVS II
TVS III TW TW Date
U4E U4R U4RB
U4RBK

CONTAX Battery Charge Tips

1. If your CONTAX battery can not charge with our CONTAX battery charger, what is matter with the charger?

I think there is some electrical contact problem in your CONTAX charger and you can fix it yourself in a few minutes.

(1). Remove your CONTAX charger from the DC adapter.
(2). There are two hooks at the bottom of the CONTAX charger.
(3). Your can release the top charging plate by pushing the hooks with two fingers.
(4). The top charging plate will release from the top.
(5). At the bottom of the charging plate, there will be three metallic contacts.
(6). Try pulling all the contacts so that it will avoid the bad connection.
(7). Slowly re-insert the charging plate to the charging base.
(8). Re-connect the DC adapter and your CONTAX charger should work.

Good luck and if there is still other problem, please don't hesitate to send us a mail again.

2. What does the light indicator mean when charging CONTAX battery ?

(1).Plug the AC power adapter in a wall outlet.
(2). Connect the AC Power adaptor supplied with CONTAX charger to the DC in jack.
(3). "Status" indicator shows RED when the CONTAX charger is ready and "Charger" indicator shows flashing Green when waiting for battery pack.
(4). Slide CONTAX battery pack in the charger and "Charger" indicator goes RED when charging.
(5). "Charger" indicator show RED and GREEN alternatively when CONTAX battery pack has more than 90% charged.
(6).When the CONTAX battery pack is fully charged, the "Charger" indicator shows a steady green.
(7). After the CONTAX battery pack fully charged, slide the battery pack out.
(8). Unplug DC power, "CHARGE" and "STATUS" indicators go out.

3.How to Test a CONTAX Battery Charger

Whether you're unsure that your CONTAX battery charger is working properly. Running a test on you CONTAX battery charger is an easy process to solve this problem.

(1).Plug in your CONTAX charger to an electrical outlet. Remove any batteries you may have charging in the unit.

(2).Turn on your voltmeter unit. Be sure there's power getting to the meter. Plug in the test probes into the voltmeter according to the meter's instructions. Set the selector switch to the highest level for DC Volt or whatever is recommended in the meter's instructions.

(3).Take a battery or battery pack that's compatible to your battery charger. Make sure the CONTAX battery has no corrosion and is not leaking fluid. Touch the positive end of the battery with the red probe. Take the black test probe and place it on the negative side of the battery.

(4).Check the readout on the voltmeter and see where the pointer is indicating to. If it's on the left side, or negative side, switch the test probes. If it's on the right side, it will show that the CONTAX battery is receiving some charge. Where it points to on the meter will determine how much charge it received.

(5).Check the CONTAX battery charger to see how much power it's giving off, if you continue to receive a negative reading from the batteries. A negative reading will indicate a bad battery charger, and you should replace it. If the charger has sufficient amount of power flowing through it, it's more than likely the CONTAX batteries are bad and just won't hold a charge.