UK Battery Charger store >> Battery Charger >> DURACELL Battery Charger suitable for DURACELL

Please Press 'Ctrl + F' to locate your drill battery number or Machine Model.

Use our cross-reference information to choose the correct DURACELL Battery Charger on Toppower(UK) Shipping. select high quality and lower price DURACELL battery charger part NO. or the machine NO. bellow:
This Battery Charger can replace the following part numbers of DURACELL
123 DL123A DL123A2 DL2/3A
DL223A DL245 DLCRV3B DR12
This is also compatible with the following models of DURACELL
DR10 DR11 Duracell Common Photo (Camera)Model

DURACELL Battery Charge Tips

1. If your DURACELL battery can not charge with our DURACELL battery charger, what is matter with the charger?

I think there is some electrical contact problem in your DURACELL charger and you can fix it yourself in a few minutes.

(1). Remove your DURACELL charger from the DC adapter.
(2). There are two hooks at the bottom of the DURACELL charger.
(3). Your can release the top charging plate by pushing the hooks with two fingers.
(4). The top charging plate will release from the top.
(5). At the bottom of the charging plate, there will be three metallic contacts.
(6). Try pulling all the contacts so that it will avoid the bad connection.
(7). Slowly re-insert the charging plate to the charging base.
(8). Re-connect the DC adapter and your DURACELL charger should work.

Good luck and if there is still other problem, please don't hesitate to send us a mail again.

2. What does the light indicator mean when charging DURACELL battery ?

(1).Plug the AC power adapter in a wall outlet.
(2). Connect the AC Power adaptor supplied with DURACELL charger to the DC in jack.
(3). "Status" indicator shows RED when the DURACELL charger is ready and "Charger" indicator shows flashing Green when waiting for battery pack.
(4). Slide DURACELL battery pack in the charger and "Charger" indicator goes RED when charging.
(5). "Charger" indicator show RED and GREEN alternatively when DURACELL battery pack has more than 90% charged.
(6).When the DURACELL battery pack is fully charged, the "Charger" indicator shows a steady green.
(7). After the DURACELL battery pack fully charged, slide the battery pack out.
(8). Unplug DC power, "CHARGE" and "STATUS" indicators go out.

3.How to Test a DURACELL Battery Charger

Whether you're unsure that your DURACELL battery charger is working properly. Running a test on you DURACELL battery charger is an easy process to solve this problem.

(1).Plug in your DURACELL charger to an electrical outlet. Remove any batteries you may have charging in the unit.

(2).Turn on your voltmeter unit. Be sure there's power getting to the meter. Plug in the test probes into the voltmeter according to the meter's instructions. Set the selector switch to the highest level for DC Volt or whatever is recommended in the meter's instructions.

(3).Take a battery or battery pack that's compatible to your battery charger. Make sure the DURACELL battery has no corrosion and is not leaking fluid. Touch the positive end of the battery with the red probe. Take the black test probe and place it on the negative side of the battery.

(4).Check the readout on the voltmeter and see where the pointer is indicating to. If it's on the left side, or negative side, switch the test probes. If it's on the right side, it will show that the DURACELL battery is receiving some charge. Where it points to on the meter will determine how much charge it received.

(5).Check the DURACELL battery charger to see how much power it's giving off, if you continue to receive a negative reading from the batteries. A negative reading will indicate a bad battery charger, and you should replace it. If the charger has sufficient amount of power flowing through it, it's more than likely the DURACELL batteries are bad and just won't hold a charge.